Transport of surface-modified iron nanoparticle in porous media and application to arsenic(III) remediation

The surface-modified iron nanoparticles (S-INP) were synthesized, characterized and tested for the remediation of arsenite (As(III)), a well known toxic groundwater contaminant of concern. The S-INP material was fully dispersed in the aqueous phase with a particle size distribution of 2–10 nm estimated from high-resolution transmission electron microscopy (HR-TEM). X-ray photoelectron spectroscopy (XPS) revealed that an Fe(III) oxide surface film was present on S-INP in addition to the bulk zero-valent Fe⁰ oxidation state. Transport of S-INP through porous media packed in 10 cm length column showed particle breakthroughs of 22.1, 47.4 and 60 pore volumes in glass beads, unbaked sand, and baked sand, respectively. Un-modified INP was immobile and aggregated on porous media surfaces in the column inlet area. Results using S-INP pretreated 10 cm sand-packed columns containing ∼2 g of S-INP showed that 100 % of As(III) was removed from influent solutions (flow rate 1.8 mL min⁻¹) containing 0.2, 0.5 and 1.0 mg L⁻¹ As(III) for 9, 7 and 4 days providing 23.3, 20.7 and 10.4 L of arsenic free water, respectively. In addition, it was found that 100% of As(III) in 0.5 mg/L solution (flow rate 1.8 mL min⁻¹) was removed by S-INP pretreated 50 cm sand packed column containing 12 g of S-INP for more than 2.5 months providing 194.4 L of arsenic free water. Field emission scanning electron microscopy (FE-SEM) showed S-INP had transformed to elongated, rod-like shaped corrosion product particles after reaction with As(III) in the presence of sand. These results suggest that S-INP has great potential to be used as a mobile, injectable reactive material for in-situ sandy groundwater aquifer treatment of As(III).     

光刻机硅片表面不平度原位检测技术

随着光刻特征尺寸的不断减小,硅片表面不平度对光刻性能的影响越来越显著.该文提出了一种新的硅片表面不平度的原位检测技术本文在分析特殊测试标记成像规律的基础上,讨论了测试标记的对准位置偏移量与硅片表面起伏高度的变化规律,提出了一种新的硅片表面不平度原位检测技术.实验表明,该技术可实现硅片表面不平度及硅片表面形貌的高准确度原位测量.该技术考虑了光刻机承片台吸附力的非均匀性对硅片表面不平度的影响,更真实反映曝光工作状态下的硅片表面不平度大小.与现有的原位检测方法相比,硅片表面不平度的测量空间分辨率提高了1.67%倍,可实现硅片表面形貌的原位检测.     

腈菌唑分子印迹聚合物的制备及识别性能研究

以腈菌唑为模板分子，采用原位分子印迹技术，制备具有特定识别性能的连续棒状分子印迹聚合物。考察了流动相中酸量对分离的影响，研究了几种结构类似物在所得分子印迹柱上的保留特性。结果表明，这种棒状分子印迹聚合物比相应的空白聚合物有高的识别性能和选择性。     

CuO/Al2O3催化剂高温固相反应的原位XRD和Raman研究

采用原位XRD和激光Raman光谱等技术对CuO/Al2O3系列催化剂高温下的表面组成和体相结构的变化进行研究.结果表明,随着焙烧温度升高,CuO首先与载体Al2O3发生固相反应生成CuAl2O4.CuAl2O4层能阻止外层CuO进一步向载体Al2O3扩散,从而使部分CuO稳定在CuO/Al2O3催化剂的表层.     

A NOVEL EOR POLYMER (Ⅱ)——INVESTIGATION ON IN-SITU GELATION OF SMRF SYSTEM IN BEREA CORE

In-situ gelation of aqueous sulfomethylated resorcinol formaldehyde (SMRF) system inBerea core has been investigated. Two sets of displacement experiments were conducted with thissystem (containing 5% NaCl, 0. 036% CaCl_2. 2H_2O). The brine permeabilities of the coreswere reduced significantly from about 600 to 0.1 md. The in-situ gelation in Berea core occurreda little bit earlier than gelation anticipated from bulk test in the experiments. The gel time waseasier to control at initial pH between 6 and 8. During injection of SMRF system, the apparentviscosity was less than 1 mPa·s at 41℃.     

原位ATR-FTIR法研究异丁烯正离子聚合反应

应用原位ATR-FTIR法可在线检测异丁烯可控，活性碳正离子聚合反应过程，文章综述了原位ATR-FTIR法的特点，并进一步介绍其在异丁烯碳正离子聚合机理和动力学研究中的应用。     

A NEW KIND OF FIBER-SPUN FROM POLYSULFONAMIDE/ZINC SOLUTION

In this paper, we succeed in fabricating high-temperature fiber of polysulfonamide/ZnO. Polysulfonamide/ZnO nanocomposite was prepared by in-situ polymerization. Some studies and characterization of Polysulfonamide/ Zinc oxide nanocomposite with ZnO 0.5% have been done. It includes ηr,, Crystal degree and thermal property. Experiment＇s results showed that, ZnO as filler can improve crystal degree of polysulfonamide fiber. The crystal degree has been bnproved, from lower than 20% up to 27%. ηr of polysulfonamide/ Zinc oxide nanocomposite solution with ZnO 0.5% is 2.03. The maxinum weight loss of the nanocomposite occurred at 453.5 ℃.     

透明导电玻璃(ITO)基材自加热传感静态芯片聚合酶链反应(PCR)

利用商品化ITO玻璃导电层的温阻效应, 无需任何微加工手段, 实现了自加热和传感的芯片温度自动程序控制, 最大程度地减小了传感滞后对温度控制稳定性的影响, 温度控制的稳定性达到了0.2 ℃, 升温速度最快可达20 ℃/s以上, 在冷却风扇辅助下降温速度最快达到了8 ℃/s. 芯片温控单元的引线从传统的两对(一对用于传感, 一对用于加热)减少为一对. 通过在该芯片上直接构建多个开放微池反应器的方法成功地实现了λDNA 157 bp片段的并行扩增. 将该芯片置于倒置荧光显微镜样品台上, 以蓝色(575 nm)发光二极管为光源, 以光电倍增管为检测手段检测了dsDNA和SYBR Green Ⅰ嵌合物的荧光强度随温度的实时变化曲线.     

含液晶聚合物的原位复合材料中界面相容性的改善策略

综述了近年来含液晶聚合物的原位复合材料中增容技术的一些进展,主要了四种增容技术,即加入具有增容作用的第三组分;在分散相液晶聚合物的主链上引入与基体树脂主链中相同或相似的单元,酯交换反应和多元共混技术,简要描术字原位复合材料的发展趋势。     

缩聚合成聚芳酯和聚酯－聚醚弹性体的微相复合物

通过原位直接缩聚反应，制备了刚性棒状聚对羟基苯甲酸酯（ＰＨＢ）和聚对苯二甲酸丁二醇酯－聚四亚甲基醚多嵌段共聚物（ＰＢＴ－ＰＴＭＧ）的微相复合物．复合物可溶于氯仿等溶剂，可以浇铸成膜．本文研究了ＰＨＢ含量和聚合过程中，基体聚合物溶液浓度对微相复合物形态以及力学性能影响．同共混法相比，原位缩聚法可得到分散更均匀，力学性能更优良的微相复合物．